Approved duty point
Confirm feed-water data, design flow and target quality before fabrication begins.
1.5 m³/h industrial reverse osmosis
1500 LPH Industrial RO Water Treatment System
A 1.5 m³/h skid-mounted reverse osmosis system engineered around your water analysis, target quality and site utilities.
Technical response within 24 hours
1.5 m³/h
Design product-water capacity
36 m³/day
At 24-hour nominal operation
PLC + HMI
Automated control option
Designed around your project
A system built for the actual water and operating duty
This 1500 LPH industrial RO system is designed for projects that need approximately 36 m³ of treated water per day at continuous operation. Instead of presenting a fixed membrane, recovery rate or final-water claim, we select the pretreatment, membranes, pressure and post-treatment from your raw-water analysis and required product-water standard.
A pretreatment recommendation based on the actual raw-water report
RO membranes, high-pressure pump, instruments and skid piping matched to the duty
PLC/HMI controls with defined alarms and operating logic
Factory test procedure, operating documentation and export packing options
Treatment process
From source water to the required output
- 1Raw-water review
- 2Pretreatment
- 3RO separation
- 4Post-treatment
- 5Product water
Application fit
Typical applications
Equipment is engineered around the source water, target quality and operating conditions of your project.
Bottled water pretreatment
Food & beverage
Boiler feedwater
Manufacturing process water
Hotels & resorts
Commercial water supply
Start with the right data
Prepare a faster quotation
Send the key project data below to shorten the technical-selection cycle and receive a more accurate equipment scope.
- Raw-water report, or at minimum TDS, hardness, iron and free-chlorine data
- Required output in m³/h or m³/day and anticipated operating hours
- Target product-water quality, application and any local compliance requirement
- Site power supply, available footprint and destination country
Built with project accountability
Equipment configurations built around the project
These workshop photographs show the type of equipment configuration we build. The final layout, components and scope are engineered around your water analysis, capacity and site requirements.
Compact skid-mounted layout
A compact treatment train keeps the key equipment accessible for installation, operation and routine service.
Integrated pump and controls package
Pumping, instrumentation and PLC controls are selected and arranged around the agreed operating duty.
Evidence before order
A project file you can review before dispatch
These are project deliverables—not generic marketing claims. The final scope is confirmed in the approved technical proposal and agreed factory-acceptance-test plan.
Project P&ID and general arrangement
Review treatment interfaces, equipment footprint and connection points against your site plan.
Component schedule
Verify the selected membrane, pump, instruments and control scope in the approved technical proposal.
FAT record and test video
Agree the test scope in advance, then receive the applicable test record and video before dispatch.
Frequently asked questions
What water quality can a 1500 LPH RO system produce?+
The final product-water quality depends on feed-water chemistry, selected membrane, recovery and post-treatment. Share your source-water report and target standard so the proposal can state a defined design duty rather than a generic claim.
Is the 1.5 m³/h capacity continuous?+
The page expresses the design product-water capacity. Daily output depends on operating hours, feed-water conditions, cleaning cycles and the final agreed duty point; at 24-hour operation, 1.5 m³/h corresponds to up to 36 m³/day.
Can this system be used for drinking-water projects?+
It can form the RO treatment stage of a drinking-water project. Final treatment, disinfection, storage and compliance requirements must be selected against the local regulation and the intended use.
What is checked before shipment?+
The agreed factory acceptance test can cover hydraulic operation, instruments, control logic, alarms and the defined duty point. The exact test scope is documented with the approved configuration.
Ready to discuss your project?
Get a configuration and quotation for 1500 lph industrial ro water treatment system.
Share your water data and required capacity. Our team will recommend a workable equipment scope.